SKU: DRFC-2873
📋 GST Invoice Available

DYS X2810 1100KV 6S Brushless Motor for Mark4 FPV Freestyle 7inch Long Range

₹1,239.00 (Inclusive of all taxes)
Out of Stock

The DYS X2810 1100KV brushless motor is engineered for 6S LiPo-powered 7-inch long-range FPV and freestyle drones, offering high torque and efficient power delivery for extended flight endurance and dynamic performance.

Features

  • 1100KV rating optimized for 6S LiPo voltage on 7-inch propellers.
  • High-torque 12N14P stator configuration (28mm diameter x 10mm height).
  • Robust 5mm hardened steel shaft for reliable power transmission.
  • Premium N52H neodymium magnets for strong magnetic field and efficiency.
  • Supports up to 52A max current and 1300W peak power output.

Out of stock

Description

The DYS X2810 1100KV motor is a purpose-built propulsion unit for 7-inch long-range and freestyle FPV quadcopters, such as the Mark4 frame. Its 1100KV winding is specifically tuned for 6S LiPo batteries, providing the ideal balance of rotational speed and torque to efficiently spin large 7-inch propellers. This results in extended flight times and smooth, controllable thrust across a wide throttle range.

Constructed with a 28mm stator and high-grade N52H magnets, the motor delivers consistent power with minimal electrical losses, evidenced by its 63.56 mΩ internal resistance. The 5mm shaft and robust bearing assembly ensure reliable operation under the high loads and vibrations typical of long-range missions and aggressive freestyle flying. Its 64g weight contributes to a favorable thrust-to-weight ratio for its class.

Key Features

  • Long-Range Optimized KV: 1100KV winding provides efficient RPM per volt on 6S, ideal for endurance-focused builds.
  • High-Torque Stator Design: 28x10mm (2810) stator size with 12N14P configuration delivers substantial low-end torque for 7-inch props.
  • Premium Magnetic Circuit: N52H-grade neodymium magnets maximize magnetic flux density for powerful and efficient operation.
  • Durable Mechanical Build: Features a 5mm hardened steel shaft and high-quality bearings for long-term reliability.
  • Thermal & Electrical Efficiency: Low internal resistance (63.56 mΩ) minimizes heat generation under load, supporting sustained high-power use.
  • Integrated Wiring: Comes pre-soldered with 250mm of 18AWG silicone wire for direct ESC connection.

Applications

  • 7-inch long-range FPV quadcopters (e.g., Mark4, other 7" LR frames).
  • 6S-powered freestyle drones requiring high torque for large propellers.
  • Endurance-focused cinematic or mapping UAVs utilizing 7-inch propellers.
  • Heavy-lift micro drones where efficient 6S power delivery is critical.

Technical Specifications

ModelX2810
KV Rating1100 KV
Motor TypeOutrunner Brushless
Stator Size28mm x 10mm (2810)
Configuration12N14P
Max Voltage6S LiPo (~25.2V)
Max Continuous Current52A
Max Power1300W
Internal Resistance63.56 mΩ
Shaft Diameter5mm
Magnet GradeN52H
Idle Current1.1A
Recommended Propeller7-inch
Weight64g
Wire Gauge & Length18AWG, 250mm

Frequently Asked Questions

What size ESC is recommended for the DYS X2810 1100KV motor?

A minimum 60A continuous-rated ESC is recommended, with 80A or higher being ideal for headroom. Ensure the ESC is compatible with 6S LiPo input voltage and supports the high pole count (12N14P) of this motor for smooth operation across the entire throttle range.

Is this motor suitable for 4S or 5S battery configurations?

While it can physically run on lower voltages, the 1100KV rating is optimized for 6S. On 4S or 5S, it will produce significantly less RPM and thrust, potentially struggling to efficiently spin large 7-inch propellers. It is strongly recommended to use it with a 6S LiPo pack for its intended performance.

What is the correct mounting pattern for the DYS X2810 motor?

The DYS X2810 uses a standard 16x19mm M3 mounting hole pattern. This is a common pattern for motors of this size class. Ensure you use high-strength M3 screws, typically 4-5mm in length, and apply thread-locker to secure them against vibration.

Package Includes

  • 1 x DYS X2810 1100KV 6S Brushless Motor
  • Pre-installed motor wires (18AWG, 250mm length)
  • Mounting hardware (screws)

Additional Information

Weight 0.064 kg